718 ABS License Plate Mounts

Need4Spd · #31

Tom wrote: Sat Sep 04, 2021 6:51 pm Chulander -- Awesome! Thank you for posting! Looking great on your car! No need to let it sit overnight, but no harm either....

Need4Spd -- I could 3D print you a set now, or in the next month or so, we should have a CNC'd version that fits both the 991 and 991.... Your choice!

lougin -- not sure I ever did mounts for the 981, though I seem to recall folks using the 991 version. If you wanted to take a picture of where your license plate mounts, I can probably tell you what would/wouldn't work....

Hi, Tom! I’m not in any hurry. Just let me know when the CNC’d version is ready! My car is a 991.1 turbo.

Tom · #32

Need4Spd wrote: Tue Sep 07, 2021 9:07 am
Tom wrote: Sat Sep 04, 2021 6:51 pm Chulander -- Awesome! Thank you for posting! Looking great on your car! No need to let it sit overnight, but no harm either....

Need4Spd -- I could 3D print you a set now, or in the next month or so, we should have a CNC'd version that fits both the 991 and 991.... Your choice!

lougin -- not sure I ever did mounts for the 981, though I seem to recall folks using the 991 version. If you wanted to take a picture of where your license plate mounts, I can probably tell you what would/wouldn't work....
Hi, Tom! I’m not in any hurry. Just let me know when the CNC’d version is ready! My car is a 991.1 turbo.

Will do, and keep your eyes open here -- I'll start a new thread when they are ready. My hope is to do a mount that fit the 981, 991.1 and.2, and the 992 (including new GT3). Those cars all have the raised ridge/outline, requiring relief grooves in the mount. I'll get those going as soon as I have enough of the 718 mounts to keep up for a while -- by the end of the month I hope.

wistful · #33

oooo... these look nice!

Tom · #34

wistful wrote: Tue Sep 07, 2021 8:08 pm oooo... these look nice!

They are popular here on Carpokes. If you want a set, let me know.

Stigs cousin · #35

Those Lic.plate mounts look really nice!CNC'ed ones look better then the 3 -D printed ones.No offense Tom!

TPatt · #36

Hi Tom,

New Porsche Cayman owner here, I'm coming over from 718forum. There was a post about these there.

I'll be ordering soon.

larry · #37

Hey Tom,

New user here, I was referred by Mitch on our little Seattle 912 group. I’ll be ordering a set of these for my Gentian Blue GT4 as soon as I hit the post count.

Thanks!

808c2s · #38

larry wrote: Sun Sep 12, 2021 11:02 pm Hey Tom,

New user here, I was referred by Mitch on our little Seattle 912 group. I’ll be ordering a set of these for my Gentian Blue GT4 as soon as I hit the post count.

Thanks!

You can just email him: admin@carpokes.com

OT-Dan · #39

Another happy customer, the mounts are great! So satisfying to tighten machined screws instead of going through the plastic bumper. Great service by Tom as well.

AdamIsAdam · #40

Hey @Tom and others. Yes, I'm here! Taa-daa! (from Renn). My CGTS4.0 is on order so I MUST start collecting parts for it. I didn't realize the dealer has to make holes in the rear bumper too in order to mount plates! I don't know of any other car, EVER, that didn't have some sort of a nut mounted for the rear plate.

SO I NEED THIS! ASAP! Because my car will be here on 12/31 (if I'm lucky).

I'll email you, Tom, since I read that I can't PM for a few posts yet.

Thanks again.
Adam